RoadsterSport Max Power NC Stainless Steel Header for RHD CARS

DESCRIPTION

This 1.6" version of our RoadsterSport Max Power header is for RHD (Right Hand Drive) cars, which cannot fit our larger 1.8" NC header. If you have a Left Hand Drive car in the US or elsewhere, this is not for you!

Comes with one "donut" gasket for header to midpipe connection included.

Gorgeous! Nothing comes close to our famous RoadsterSport MAX Power Header! Look at those smooth curves! Notice you don't see 6 welded sections for each primary like so many lesser headers that are made from cut pieces of standard radius pipe and straights, instead ultra SMOOTH all mandrel bent tube is used here to keep flow as clean as possible. Sexy all T304 polished stainless steel is formed into equal length primaries for max power.

We put incredible effort into making the exit at the collector as smooth and perfect as we can get it because this collection point is the KEY to good header flow and we had to make sure this was done as perfect as possible. Note we use the factory collector gasket....so our fit is as factory-like as possible.

Our collector outlet is 2.5 inches. Curiously, the factory outlet is ALSO 2.5 inches and then the factory exhaust chokes down after that point. For best performance customers should match our header with our midpipe and exhaust so they are running 2.5 inches of flow all the way... but our header will bolt in place of the factory header and connect perfectly to the factory midpipe. Note that we have no O2 sensor connection in our header....in part to keep flow as clean as we can get it but also because we could see no purpose in locating them in the header since doing so will throw a code because pulling the factory header includes removal of the first catalytic converter.

OXYGEN SENSORS:

Several options on what to do with the O2 sensors with our header. Read below for options A, B and C. Optional oxygen sensor wire extension cables are available as an add-on option with this header. Adding ONE wire extension gets you one long wire extension to move the secondary oxygen sensor to the midpipe as described in option B below. Adding TWO wire extensions gets you one long and one short wire extension for moving both primary and secondary oxygen sensors down to the midpipe as described in option A below.

A) Buy our midpipe and our two wiring extensions available here for simple plug and play install. Our midpipes are designed to take both O2 sensors, and includes two O2 sensor connections for that - one before the midpipe's converter and one after the midpipe's converter to help avoid a code. Buy BOTH of our extensions for that option.

B) Second choice and most common choice is first sensor in the header and second sensor in our midpipe after the converter, which will also avoid a code. For install in the midpipe of both sensors you need both O2 extension cords, but if you put the first sensor in the header you only need an extension for the second sensor. The first sensor will reach header connection but you may have to follow the wires back to the harness and use a razor blade to clear some sheath which has them gathered shorter than they actually are.

C) Third choice is to put BOTH sensors in the header, which will cause a code unless your tuner turns off the code caused by having the second sensor in the header. You don't need any wiring extensions for that option (sensors will reach header connection but you may have to follow their wires back to the harness and use a razor blade to clear some sheath which has them gathered shorter than they actually are).

CARB NOTICE: Installing this header in the 2006 through 2015 MX5 Miata means removing the first catalytic converter which means this header will NEVER be a California street legal header, never be CARB approved (and therefore legal in California for off road use only). Sorry, we will not ship these to residents of California.

BRIAN'S APPLICATION NOTES: This is THE header for peak power on the NC with 2.0 liter motor. Our normally aspirated customers making the most power, and our supercharger customers making the most power, are all using this header. In the forums folks are proud to show off lesser headers that have 5 to 8 welded sections for each primary because the maker did it the cheap way with welding up standard straights and radius bits but while they are admiring the welds they overlook that each of those weld points means that inside the pipe you have a rough circle of material instead of smooth pipe! In contrast, you don't see welds on every primary here because we do it right, smooth mandrel custom bend complete one piece primary sections give you the smoothest possible flow.

The first converter is also a pretty good resonator so understand that installation of any header will raise the exhaust sound level a good 20%. Therefore, we strongly recommend the RoadsterSport Q muffler with any header change because it was designed to handle the sound level of the header, and our RoadsterSport Helmholtz midpipe tunes the final sound result for drone free fun.

YES, fits both Manual and Auto trans. Those with AUTOMATIC transmission should read our instructions on install first.

INSTRUCTIONS: Read full installation hints and notes in our forum Installation Instruction Section! --- CLICK HERE TO READ MORE. YES, fits both manual and automatic.

SOUND Files and DYNO at our Exhaust Blog---CLICK HERE TO LISTEN AND READ MORE.

PICTURE OF FACTORY HEADER BELOW, Note the pinch point circled in red, which chokes the power this motor can otherwise make.

Compare the short and uneven length factory header primaries above to the equal LENGTH, LONG and SMOOTHLY curved primaries of the RoadsterSport MAX Power Header:

.

Take a ride in our 2006 with this full RoadsterSport Header, Midpipe and Exhaust.